Monoether anhydride--odpa

1. Brief introduction

3,3’,4,4’-Oxydiphthalic anhydride(simply called monoether anhydride) is a very useful chemical intermediate, which can be further prepared for many compounds, and be used as the excellent property modifier for resins. In particular, the polyimide synthesized from the monoether anhydride has remarkable mechanical properties, high electrical insulation property, high radiation resistance and chemical stability. It has become an important and invaluable material in the field of electrical insulation material, and miniature, high capacity and high heat resistant electrodes. It also has a high valuable use for manufacturing high temperature non-lubrication bearings.   

2. Specification                 CAS NO. 1823-59-2

molecular formula	C16H6O7
molecular weight	310.2
purity	≥99%
appearance	creamy white powder
melting point	227 - 230℃
metallic ion content:
sodium ion（mg/kg）	≤5
chlorion（mg/kg）	≤5
ferric ion（mg/kg）	≤5

3. Use

This product is mainly used for preparing polyimide goods with high purity and high property. It has excellent thermo- and oxidative stability, radiation resistance, wearing resistance, it is also flame retardant, low smoking, and can be used for composite material, forming and adhesive agents, mould goods, films, micro-electronic products, and gas separation films, etc. It is used as a latent curing agent of epoxy resin in the process of micro-encapsulation.

6050 Polyimide Film

Polyimide film is condensed with 4-formic acid-2-anhydride of benzene, and 4.4 -diamino-biphenyl-ether oxide. It has high low-temp resistance, radiation hardening and good Dielectric.

Technique Requirements
1.Appearance: film is surfacing, unbubbly, non-pinholedand without any conduction admixture.
2.Width and Length: film is offered on roll or coil, Width 10-500mm is utilized for compound rolled conducting wire, each roll is not less than 300m, if for the other electronic engineering material, each roll is not less than 50m. According to the customer's request, the Pellicle can be banding, but its width and length should be consucted with the two parties.
3.The Depth, Spec and Thlerance number of film.

Standard Depth (mm)	Tolerance
0.01	±0.002
0.025	±0.0025
0.03	±0.002-0.003
0.05	±0.005
0.075	±0.0075
0.1	±0.01
0.15	±0.010
0.20	±0.010

4.Film Performance

Item Name		Unit	Standard
TensileStrength	Portrait	Mpa	≥135
	Cross direction		≥115
Elongation at Break	Portrait	%	≥35
	Cross direction		≥35
Line-frequency Electric Intension	Average	MV/m	≥150
	Specific		≥100
Volume Resistance		Ω※cm	≥1.0×1010
Surface Resistance		Ω	≥10×1013

Polyimide Thermosetting Adhesive Film

Polying Thermosetting Adhesive film is thermosetting compound material that polyimide film is immersed and covered with macromolecule adnesive of Organic silicons after sintering low temperature.
The Material is on 130℃6Hours
160℃　?4Hours
?80℃　?2Hours
solidifying, can be insulation for Fand H-class rolled conducting wire, which is made to F and H-class electric motor.

S.N.	Item Name		Unit	Technique Indicator
1	Appearance		——	Surface bright and clean, unbubbly and without mechanical admixture
2 3	Specification	Thickness (Deviation)	mm	0.03 or 0.05(±0.005-0.015)
		Width	mm	10-500 Different kinds of strips be supplied as per customer's requirement
		Length	m	≥30
4	Tensile Strength		Kg/mm2	≥8
5	Elongation	Vertical	%	≥25
		Cross direction	%	≥20
6	Breaking Strength		KV/mm	≥100
7	Stripping Strength		g/25mm	≥400
8	Heat Resistance		℃	Used underthe condition of 180℃

H-class Polyimide Glass varnished cloth

Polyimide Glass varnished cloth is made with the class cloth without Alkli, which covered with H-class polyimide adhesion after firing, it can be used under 200℃.
Polyimide Glass varnished cloth has high temperature resistance, radiation hardening resistance, solvent resistance and dielectric property. It's applicable to the insulation of high-temp resistant motor electrical appliances, the lining and wrapping of electric welding set.

S.N	Item Name		Unit	Technique Indicator
1 2	Specification	Thickness (Deviation)	mm	0.10-0.20(±0.02)
		Width	mm	≥500
		Length	m	≥20
3	Tensile Strength		Kg/mm2	≥10
4	Volume Resistance modulus		Ω.mm	≥1×1012-13
5	Disruptive Voltage	0.15mm 0.20mm	kv	≥5
		0.06mm 0.10mm 0.12mm	kv	≥2.5
6	Dielectric Constant 50Hz		—	≤3.5
7	Dielectric Loss Angle50Hz		—	≤0.01
8	Dissove and acid resistance		—	Add in strong solvent(Acetamide, Formamide) and strong acid with 1% liquor for 24 hours, lacquer film should not fall off.

HFG Compound Film

HFG Copmound film is compounded with HF Compound film and FG Pellicle varnished cloth, especially for H and F specific electrical motor, e.g.diving-oil, diving-bittern, diving and drilling machine. It has good electric insulation, physicomechanical properties, heat resistance, smooth lubrication, oil and dissolve resistivity.

S.N.	Indication Name		Unit	Technique Indication
1	Appearance		—	Fawn-colored surfacing and few FG buckling surface is permitted
2	Specification	Thickness	mm	0.10-0.13
		Length		≥20
3	Tensile Strength		Kg/m2	≥80
4	Volume resistance		Ω.cm	≥1014
5	Breaking Strength		Kv/mm	≥50

HF and FHF Compound Film (Polyimide Compound film)

Polyimide Compound film (FH. FHF) is single or double covered with F-46, This has high/low temperature resistance, electric insulation, radiation hardening resistance and hermetization under high temp. it can be utilized as insuation for wire, cable and electronmagnetic wire.

S.N	Indication Name		Unit	Technique Indication
				FH	FHF
1	Appearance		——	Transparent or Semi-transparement Golden Yellow Pellicle
2	Specification	Thickness (Deviation)	mm(%)	0.0375-0.12 (±8)	0.04-0.12 (±8)
		Width	mm	8-500	8-500
		Length	m	≥500	≥500
3	Tensile Strength		Mpa	≥120	≥120
4	Elongation		%	≥40	≥40
5	Stripping Strength (Adhesive of Fluovin for pellice)		N/25mm	≥6	≥6
6	Linefrequency ElectricIntension		MV/m	≥1.5	≥1.5
7	Volume Resistance 200℃		Ω.cm	≥1.0×1010	≥1.0×1010
8	Relative Dielectric Constant 50Hz		—	≤3.9	≤3.9
9	Dielectric loss Factor 50Hz		—	≤1.0×10-3	≤1.0×10-3

Polyimide H-class Pressure-sensitive Tape

Polyimide Pressure-Sensitive tapes are made by that Polyimide films are immersed and covered with that Pressure-sensitive adhesive is made up of two adhesive-Crylic acid and Silicone as main raw material under sintering, with characters of autohension, good stripping strength and shearing strength. Polyimide Pressure0sensitive Tape can be utilized on -70℃-200℃ for quite a long time. It's for all kinds of H-class electrical ator, electrical equipment.

Indication			Unit	Technique Indicator
1	Appearance		—	shows golden-yellow surfacing smooth, autohesive, unlayered and unbubbly
2	Specification	Thickness (Deviation)	mm	0.05-0.07 (0.005-0.01)
		Width	mm	Different kinds of tapes be supplied as per customer's requirement
3	Tensile Strength		Kg/mm2	≥10
4	Elongation		%	≥25
5	Breaking Strength 20℃+5℃		KV/mm	≥100
6	Volume Resistance		Ω.cm	≥1.0×1013
7	Surface Resistance		Ω.cm	≥1.0×1012
8	Dielectric loss angle Tangent 50Hz		—	≤0.01
9	Dielectric Coefficient 50Hz		—	≤4
10	Stripping-force N/25mm		—	≥6.2

CF6246 Mylar Adhessive Tape

Mylar Adhesive Tape is covered with Crylic Acid adhesive after drying. It has character of autohesion, stripping strength and shearing strength. It can be used under -20℃-160℃ for quite a long time with unchangeable adhesion. It can be utilized as insulation wrapping and connection for F-class Electric machine, conducting wire and Electric appliances. There are two kinds of adhesive tape: single adhesive tape and double adhesive tape.

Indication Name			Technique Indicator	Means
1	Appearance		Surfacing Smooth unbubby,unlayered and Autohesion	Visualization
2	Specification		Length、Thickness: 0.06×25m Different width of tapes can be made as per customers's require (Tolerance:0.005-0.01)	GB/T13541-92
3	Tensile Strength ≥N/10mm		800/mm	GB/T13541-92
4	Elongation %		80
5	Adhesive forSteel and Steels ≥N/10mm		2	GB/T2792-98
6	Adhesive for bottom >N/10mm		2	GB/T2792-98
7	Disruptive Strength 20℃+5℃		70KV/mm	GB/T13541-92
8	Surface Resistance		1×1012Ωcm	GB/T13541-92

More new products...